raspberry pi 运行状态提醒

发表于 分类于 阅读次数： 本文字数： 757 阅读时长 ≈ 3 分钟

1.获取运行状态

获取树莓派运行状态用到的命令如下表：

命令 说明
vcgencmd measure_temp 获取CPU温度
top 获取CPU使用率
free 获取RAM使用率
df 获取DISK使用率
ifconfig 获取IP地址
  • 1.1 获取CPU温度：
1
2
3
$ vcgencmd measure_temp
    temp=40.8C   
# 直接返回温度，只要把 temp= 去掉就行
  • 1.2 获取CPU使用率
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
$ top -bn1
    top - 16:27:28 up 1 day, 18:49,  1 user,  load average: 0.00, 0.00, 0.00
    Tasks: 105 total,   1 running, 104 sleeping,   0 stopped,   0 zombie
    %Cpu(s):  1.4 us,  2.7 sy,  0.0 ni, 95.9 id,  0.0 wa,  0.0 hi,  0.0 si,  0.0 st
    MiB Mem :    926.1 total,    697.2 free,     51.3 used,    177.6 buff/cache
    MiB Swap:    100.0 total,    100.0 free,      0.0 used.    797.4 avail Mem

    PID USER      PR  NI    VIRT    RES    SHR S  %CPU  %MEM     TIME+ COMMAND
    411 pi        20   0   10188   2804   2500 R   5.9   0.3   0:00.04 top
    ...
    ...
# -bn1 参数： n1指定只运行一次，b输出结果为batch-mode，避免出现乱码
# 可以看到CPU的信息在第3行，只要输出CPU这一行

$ top -bn1 | awk '/Cpu\(s\)/'
    %Cpu(s):  1.4 us,  2.7 sy,  0.0 ni, 95.9 id,  0.0 wa,  0.0 hi,  0.0 si,  0.0 st
# 缩写分别是user, system, nice, idle, wait, ...
# 计算CPU使用率等于 1 - idle%
  • 1.3 获取RAM使用率
1
2
3
4
5
6
7
8
9
10
$ free -m
                total        used        free      shared  buff/cache   available
    Mem:            926          52         696          23         177         796
    Swap:            99           0          99
# -m 参数是指定输出结果以 MB 为单位
# 修改一下命令，只要输出 Mem 这一行

$ free -m | awk '/Mem/'
    Mem:            926          52         696          23         177         796
# 计算RAM使用率等于 (total - available) / total； （仅供参考）
  • 1.4 获取DISK使用率
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
$ df -h
    Filesystem      Size  Used Avail Use% Mounted on
    /dev/root        29G  1.7G   27G   6% /
    devtmpfs        459M     0  459M   0% /dev
    tmpfs           464M     0  464M   0% /dev/shm
    tmpfs           464M   24M  440M   6% /run
    tmpfs           5.0M  4.0K  5.0M   1% /run/lock
    tmpfs           464M     0  464M   0% /sys/fs/cgroup
    /dev/mmcblk0p1  253M   53M  200M  21% /boot
    tmpfs            93M     0   93M   0% /run/user/1000
# -h 参数是指定输出结果人性化，自动选择单位
# 修改一下命令，只要输出 /dev/root 这一行

$ df -h | awk '/root/'
    /dev/root        29G  1.7G   27G   6% /
  • 1.5 获取 IP 地址
1
2
3
4
5
6
7
8
9
10
11
$ sudo ifconfig wlan0
    wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
            inet 192.168.1.12  netmask 255.255.255.0  broadcast 192.168.1.255
            ...
            ...
# ifconfig 命令要用管理员运行
# wlan0 参数是指wifi网络；如果是有线网络，改为： eth0
# 修改一下命令，只要输出 inet 这一行

$ sudo ifconfig wlan0 | awk '/inet/'
    inet 192.168.1.12  netmask 255.255.255.0  broadcast 192.168.1.255

2. 完整的代码

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
import os
import time
import requests

def now():
    return '[' + time.strftime('%Y-%m-%d %H:%M:%S') + ']'

# run command
def run_cmd(cmd):
    p = os.popen(cmd).readline().strip().split()
    return p

cpu_temp = run_cmd(" vcgencmd measure_temp ")
cpu_stat = run_cmd(" top -bn1 | awk '/Cpu\(s\)/' ")
cpu_used = 1 - float(cpu_stat[7])/100.0

ram_stat = run_cmd(" free -m | awk '/Mem/' ")
ram_used = (int(ram_stat[1]) - int(ram_stat[6])) / float(ram_stat[1])

dsk_stat = run_cmd(" df -h | awk '/root/' ")
ipconfig = run_cmd("sudo ifconfig wlan0 | awk '/inet/'")
print(cpu_temp, cpu_stat, cpu_used, ram_stat, ram_used, dsk_stat, ipconfig, sep='\n')

###
status = now() + '\n\n'
status += 'Raspi Status:       \n'
status += 'CPU  Used  = {:.2%} \n'.format(cpu_used)
status += 'CPU  Temp  = {}     \n'.format(cpu_temp[0].replace('temp=', ''))
status += 'RAM  Total = {}M    \n'.format(ram_stat[1])
status += 'RAM  Used  = {:.2%} \n'.format(ram_used)
status += 'DISK Total = {}     \n'.format(dsk_stat[1])
status += 'DISK Used  = {}     \n'.format(dsk_stat[2])
status += 'DISK Perc  = {}     \n'.format(dsk_stat[4])
status += 'IP Address = {}     \n'.format(ipconfig[1])

print(status)

# Send to ftqq
key = 'SCUxxxxxxxxxxxxxxx'
api = 'https://sc.ftqq.com/{}.send'.format(key)
send_data = {'text': 'Raspi_Status', 'desp': status}
res = requests.post(api, data=send_data)
print(res.content)

# Send to wechat
import wechat_push as wp

access_token, _ = wp.get_access_token(wp.corp_id, wp.corp_secret)
wp.wechat_push_text(agent_id=wp.agent_id, access_token=access_token, message=status)